EAZYLife STEM LAB · LEARNING DIRECTORY

Electronics
Fundamentals.

Explore the building blocks of electronics through independent lessons, interactive experiments and practical workshop activities. Choose a topic and learn at your own pace.

Free open learning Independent modules Practical focus
CHOOSE A MODULE

Learn one concept at a time

Each module has its own page, so you can open, bookmark and share lessons independently.

BEGINNER FOUNDATIONS
Showing 29 of 29 modulesSearch titles, descriptions and topics
MODULE 01 · AVAILABLE

Potentiometer to LED

Use a variable resistor as an input, read its position and control LED brightness with PWM.

Open lesson
MODULE 02 · AVAILABLE

Component identification and polarity

Recognise common components, read resistor values and identify polarised terminals.

Open lesson
MODULE 03 · AVAILABLE

Voltage, current and resistance

Understand Ohm's law, compare series and parallel circuits, practise multimeter measurements and investigate battery configurations.

Open lesson
MODULE 04 · AVAILABLE

Resistors in practical circuits

Select resistors for LEDs, understand power ratings, explore voltage dividers and use resistors in practical signal circuits.

Open lesson
MODULE 05 · AVAILABLE

Diodes and LED circuits

Understand diode polarity, forward and reverse bias, LED current limiting, rectification and protection circuits.

Open lesson
MODULE 06 · AVAILABLE

Capacitors and energy storage

Explore capacitor types, polarity, charge, stored energy, RC timing, filtering and safe measurement.

Open lesson
MODULE 07 · AVAILABLE

Inductors and Magnetic Fields

Explore magnetic fields, inductance, stored energy, RL timing, switching transients and flyback protection.

Open lesson
MODULE 08 · AVAILABLE

Transistors and Electronic Switching

Explore BJT and MOSFET operation, switching, biasing, base and gate drive, relay and low-voltage motor control.

Open lesson
MODULE 09 · AVAILABLE

Operational Amplifiers and Basic Analog Circuits

Learn op-amp terminals, feedback, comparators, amplification, signal conditioning and practical analog models.

Open lesson
MODULE 10 · AVAILABLE

The 555 Timer: Timing, Oscillators and Control

Build astable, monostable and bistable circuits; explore Schmitt-trigger action, pulse-width modulation, voltage-controlled oscillation and missing-pulse detection.

Open lesson
MODULE 11 · AVAILABLE

Power Supplies and Voltage Regulation

Explore rectification, smoothing, linear regulators, buck converters, ripple, load regulation, thermal design and practical supply testing.

Open lesson
MODULE 12 · AVAILABLE

Power Supply Protection and Battery Systems

Understand fuses, polarity protection, battery chemistry, series/parallel configurations, capacity, energy, runtime and safe battery use.

Open lesson
MODULE 13 · AVAILABLE

Workshop Practice, Soldering and PCB Fundamentals

Learn workshop safety, through-hole soldering, joint inspection, continuity testing, perfboard construction and PCB design fundamentals.

Open lesson
MODULE 14 · AVAILABLE

Workshop Measurement and Instrumentation

Use a digital multimeter, understand oscilloscope waveforms, work with signal generators and interpret measurements safely.

Open lesson
MODULE 15 · AVAILABLE

Analog Sensors and Signal Conditioning

Explore LDRs, thermistors, sensor dividers, ADC conversion, filtering, buffering and practical Arduino sensor interfaces.

Open lesson
MODULE 16 · AVAILABLE

Digital Sensors and Communication Interfaces

Understand digital outputs, logic levels, pull-ups, I²C, SPI, UART and practical Arduino sensor communication.

Open lesson
MODULE 17 · AVAILABLE

Microcontrollers and Embedded Programming

Understand MCU architecture, GPIO, ADC, PWM, timers, interrupts, memory and responsive Arduino firmware.

Open lesson
MODULE 18 · AVAILABLE

Embedded Systems Design and Real-Time Control

Design reliable firmware with requirements, state machines, scheduling, deadlines, watchdogs, fault handling and feedback.

Open lesson
MODULE 19 · AVAILABLE

Digital Control, Motor Control and Feedback Systems

Explore PWM, H-bridges, encoders, open-loop and closed-loop speed control, and PI/PID fundamentals.

Open lesson
MODULE 20 · AVAILABLE

Robotics and Mechatronic Systems

Understand robot architectures, differential-drive motion, sensors, actuators, integration and a practical line-following rover.

Open lesson
MODULE 21 · AVAILABLE

Robotics Sensors, Navigation and Autonomy

Explore sensor fusion, localisation, mapping, path planning, obstacle-aware behaviour and an autonomous rover practical.

Open lesson
MODULE 22 · AVAILABLE

Wireless Communication and IoT Systems

Explore Wi-Fi, Bluetooth, network architecture, HTTP, MQTT, IoT telemetry, security and a practical ESP32 local sensor dashboard.

Open lesson
MODULE 23 · AVAILABLE

Integrated Circuits and Logic Gates

Understand IC packages, digital logic levels, AND, OR, NOT, NAND, NOR and XOR gates, truth tables and a practical 74HC08 circuit.

Open lesson
MODULE 24 · AVAILABLE

Combinational Logic Design

Design and simplify Boolean functions, use universal gates, explore multiplexers, decoders and adders, then build a practical half-adder.

Open lesson
MODULE 25 · AVAILABLE

Sequential Logic, Flip-Flops and Digital Memory

Explore latches, D, JK and T flip-flops, clock timing, counters, shift registers and build a synchronous two-bit binary counter.

Open lesson
MODULE 26 · AVAILABLE

Digital Displays and Human Interfaces

Explore seven-segment displays, multiplexing, matrix keypads, LCDs, OLEDs and build an Arduino keypad-and-LCD interface.

Open lesson
MODULE 27 · AVAILABLE

DAC and Signal Generation

Explore DAC resolution, R-2R ladders, PWM filtering, waveform generation and practical signal measurement.

Open lesson
MODULE 28 · AVAILABLE

Electronics Product Design

Turn a real need into a testable product through requirements, architecture, component selection, prototyping and verification.

Open lesson
MODULE 29 · AVAILABLE

Applied Electronics Projects

Apply circuit, embedded, sensing, control and robotics knowledge through practical project briefs, build stages and test evidence.

Open lesson

Modules are independent learning units. Suggested foundations are shown where useful, but you can explore topics in the order that makes sense to you.

LEARNING APPROACH

Understand it. Test it. Build it.

Lessons combine clear explanations, honest interactive models, practical build guidance and challenges. A simulation is labelled according to what it actually represents, not presented as a perfect hardware emulator.

Learn

Understand the principle, terminology and important relationships.

Experiment

Change variables, observe model behaviour and answer investigation prompts.

Build

Take suitable low-voltage activities to a real breadboard or workbench.

KEEP LEARNING · GO FURTHER

Free to learn. More support when you need it.

Use the open lessons and experiments at your own pace. For personalised explanations, project-specific troubleshooting, guided practical training or masterclasses, EazyLife offers paid support tailored to your learning goals.

Free or sponsored lesson referrals may be available through active programmes; they are not guaranteed.

Enquire about guidance